紅外一氧化碳分析儀用于檢測環境中一氧化碳濃度并提供預警。其采用非色散紅外線技術（即一氧化碳對紅外光譜的選擇性吸收）作為檢測原理，配備精密設計的光學吸收池和穩定可靠的電路，同時在軟件上采用修正算法對CO濃度進行修正，保證其在全量程范圍內有良好的線性度與較小的測量誤差。下面我們來該儀器的具體校準方法和開機測量步驟。
紅外一氧化碳分析儀的零點校準：
空氣中一氧化碳濃度一般為0～2.5ppm。當儀器連續運行較長時間后，會出現零點漂移，用戶需每隔若干小時進行一次零點校準。用戶可選擇氮氣校準或催化校準。
當選擇氮氣校準時，具體操作為：給儀器通入純氮氣（零氣），流量大約為1-1.2L/min，在“參數設置”界面點擊“氮氣校準”。此時“剩余時間”會開始進行倒計時，結束時校準完成，“零點值”會更新。
當選擇催化校準時，具體操作為：直接在“參數設置”界面點擊“催化校準”，儀器即開啟校準過程。此時“剩余時間”會開始進行倒計時，結束時校準完成，“零點值”會更新。
開機與測量：
紅外一氧化碳分析儀有兩種供電方式，交流供電和蓄電池供電，儀器默認使用交流供電。交流供電時，將面板上的“電池-外接”轉換開關撥到“外接”處，將220V轉10.9V電源適配器輸出插頭插在儀器面板的外接電源處，另一端連接到220V市電；采用電池供電時，將面板上的“電池-外接”轉換開關撥到“電池”處，按下電源開關，紅色指示燈亮。觸摸屏顯示內容包括一氧化碳濃度、溫度、濕度、時間、電池電量，儀器每秒鐘更新一次數據。待儀器預熱后，即可穩定測量環境中一氧化碳濃度。
地址：南京市江寧區清水亭東路1318號凱騰工業園13#
手機： 17705175021
郵箱：927962107@qq.com
手機號